Rip Routing Configurations
In this article I will demonstrate an example of
Rip Routingconfigurations. We will use four different series router so you can get familiar with all different platform covered in CCNA exam. Create a topology as shown in figure.
IP RIP comes in two different versions: 1 and 2. Version 1 is a distance vector protocol and is defined in RFC 1058. Version 2 is a hybrid protocol and is defined in RFCs 1721 and 1722. The CCNA exam now primarily focuses on version 2. There are no major differences between RIPv1 or RIPv2 so far configurations concern. To read more about differences between RIPv1 or RIPv2 or know about the characteristics read our pervious article about RIP.
| 1841 Series Router0 (R1) |
| FastEthernet0/0 | Serial0/0/0 |
| IP address | 10.0.0.1 | 20.0.0.1 |
| Connected With | Pc0 | R2 on Serial 0/0 |
|
| 2811 Series Router0 (R4) |
| FastEthernet0/0 | Serial0/0/0 |
| IP address | 50.0.0.1 | 40.0.0.2 |
| Connected With | Pc1 | R3 on Serial 0/0 |
|
| 2621XM Series Router0 (R3) |
| FastEthernet0/0 | Serial0/0/0 |
| IP address | 30.0.0.2 | 40.0.0.1 |
| Connected With | FastEthernet0/0 | R4 on Serial 0/0/0 |
|
| 2620XM Series Router1 (R2) |
| FastEthernet0/0 | Serial0/0 |
| IP address | 30.0.0.1 | 20.0.0.2 |
| Connected With | R3 on FastEthernet0/0 | R1 on Serial 0/0/0 |
|
| PC-PT PC0 |
| FastEthernet0 | Default Gateway |
| IP address | 10.0.0.2 | 10.0.0.1 |
| Connected With | R1 on FastEthernet0/0 |
|
|
| PC-PT PC1 |
| FastEthernet0 | Default Gateway |
| IP address | 50.0.0.2 | 50.0.0.1 |
| Connected With | R4 on FastEthernet0/0 |
|
|
To configure any router double click on it and select CLI. To configure this topology use this step by step guide.
(1841Router0) Hostname R1
To configure and enable rip routing on R1 follow these commands exactly.
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R1
R1(config)#interface fastethernet 0/0
R1(config-if)#ip address 10.0.0.1 255.0.0.0
R1(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R1(config-if)#exit
R1(config)#interface serial 0/0/0
R1(config-if)#ip address 20.0.0.1 255.0.0.0
R1(config-if)#clock rate 64000
R1(config-if)#bandwidth 64
R1(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down
R1(config-if)#exit
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
R1(config)#router rip
R1(config-router)#network 10.0.0.0
R1(config-router)#network 20.0.0.0
R1(config-router)#exit
R1(config)#
(2620XM-Router1) Hostname R2
To configure and enable rip routing on R2 follow these commands exactly.
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R2
R2(config)#interface serial 0/0
R2(config-if)#ip address 20.0.0.2 255.0.0.0
R2(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up
R2(config-if)#exit
R2(config)#interface fastethernet 0/0
R2(config-if)#ip address 30.0.0.1 255.0.0.0
R2(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
R2(config-if)#exit
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R2(config)#router rip
R2(config-router)#network 20.0.0.0
R2(config-router)#network 30.0.0.0
R2(config-router)#exit
R2(config)#
(2620XM-Router2)Hostname R3
To configure and enable rip routing on R3 follow these commands exactly.
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R3
R3(config)#interface fastethernet 0/0
R3(config-if)#ip address 30.0.0.2 255.0.0.0
R3(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R3(config-if)#interface serial 0/0
R3(config-if)#ip address 40.0.0.1 255.0.0.0
R3(config-if)#clock rate 64000
R3(config-if)#bandwidth 64
R3(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0, changed state to down
R3(config-if)#exit
%LINK-5-CHANGED: Interface Serial0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up
R3(config)#router rip
R3(config-router)#network 30.0.0.0
R3(config-router)#network 40.0.0.0
R3(config-router)#exit
R3(config)#
(2811Router3) Hostname R4
To configure and enable rip routing on R4 follow these commands exactly.
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface serial 0/0/0
Router(config-if)#ip address 40.0.0.2 255.0.0.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
Router(config-if)#exit
Router(config)#interface fastethernet 0/0
Router(config-if)#ip address 50.0.0.1 255.0.0.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
R4(config)#router rip
R4(config-router)#network 40.0.0.0
R4(config-router)#network 50.0.0.0
R4(config-router)#exit
R4(config)#
PC-1
PC>ipconfig
IP Address......................: 10.0.0.2
Subnet Mask.....................: 255.0.0.0
Default Gateway.................: 10.0.0.1
PC>ping 50.0.0.2
Pinging 50.0.0.2 with 32 bytes of data:
Reply from 50.0.0.2: bytes=32 time=156ms TTL=124
Reply from 50.0.0.2: bytes=32 time=127ms TTL=124
Reply from 50.0.0.2: bytes=32 time=156ms TTL=124
Reply from 50.0.0.2: bytes=32 time=140ms TTL=124
Ping statistics for 50.0.0.2:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 127ms, Maximum = 156ms, Average = 144ms
PC>
PC-2
PC>ipconfig
IP Address......................: 50.0.0.2
Subnet Mask.....................: 255.0.0.0
Default Gateway.................: 50.0.0.1
PC>ping 10.0.0.2
Pinging 10.0.0.2 with 32 bytes of data:
Reply from 10.0.0.2: bytes=32 time=140ms TTL=124
Reply from 10.0.0.2: bytes=32 time=141ms TTL=124
Reply from 10.0.0.2: bytes=32 time=157ms TTL=124
Reply from 10.0.0.2: bytes=32 time=156ms TTL=124
Ping statistics for 10.0.0.2:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 140ms, Maximum = 157ms, Average = 148msYou can verify that RIP is running successfully via show ip protocols command in privilege mode.
R1#show ip protocols
Routing Protocol is "rip"
Sending updates every 30 seconds, next due in 2 seconds
Invalid after 180 seconds, hold down 180, flushed after 240
Outgoing update filter list for all interfaces is not set
Incoming update filter list for all interfaces is not set
Redistributing: rip
Default version control: send version 1, receive any version
Interface Send Recv Triggered RIP Key-chain
FastEthernet0/0 1 2 1
Serial0/0/0 1 2 1
Automatic network summarization is in effect
Maximum path: 4
Routing for Networks:
10.0.0.0
20.0.0.0
Passive Interface(s):
Routing Information Sources:
Gateway Distance Last Update
20.0.0.2 120 00:00:20
Distance: (default is 120)
R1#
You can use show ip route command to troubleshoot rip network. If you did not see information about any route checks the router attached with that network.
R1#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
C 10.0.0.0/8 is directly connected, FastEthernet0/0
C 20.0.0.0/8 is directly connected, Serial0/0/0
R 30.0.0.0/8 [120/1] via 20.0.0.2, 00:00:01, Serial0/0/0
R 40.0.0.0/8 [120/2] via 20.0.0.2, 00:00:01, Serial0/0/0
R 50.0.0.0/8 [120/3] via 20.0.0.2, 00:00:01, Serial0/0/0
R1#To test rip routing do ping from pc1 to pc2 and vice versa. If you get replay then you have successfully configured rip routing but if you did not get replay double check this configuration and try to troubleshoot. I have uploaded a configured and tested topology in case you are unable to locate the problem spot then download this configuration file. And try to find out where have you committed mistake.
| Commands | Descriptions |
| Router(config)#router rip | Enables RIP as a routing protocol |
| Router(config-router)#network w.x.y.z | w.x.y.z is the network number of the directly connected network you want to advertise. |
| Router(config)#no router rip | Turns off the RIP routing process |
| Router(config-router)#no network w.x.y.z | Removes network w.x.y.z from the RIP routing process. |
| Router(config-router)#version 2 | RIP will now send and receive RIPv2 packets globally. |
| Router(config-router)#version 1 | RIP will now send and receive RIPv1 packets only |
| Router(config-router)#no auto-summary | RIPv2 summarizes networks at the classful boundary. This command turns autosummarization off. |
| Router(config-router)#passive-interface s0/0/0 | RIP updates will not be sent out this interface. |
| Router(config-router)#no ip split-horizon | Turns off split horizon (on by default). |
| Router(config-router)#ip split-horizon | Re-enables split horizon |
| Router(config-router)#timers basic 30 90 180 270 360 | Changes timers in RIP: 30 = Update timer (in seconds) 90 = Invalid timer (in seconds) 180 = Hold-down timer (in seconds) 270 = Flush timer (in seconds) 360 = Sleep time (in milliseconds) |
| Router#debug ip rip | Displays all RIP activity in real time |
| Router#show ip rip database | Displays contents of the RIP database |
No comments:
Post a Comment